Periodic cleaning is one of the most important tasks to extend the life of a pool pump. Knowing how to clean the pool pump correctly avoids loss of flow, overheating, abnormal noises and unnecessary electrical consumption. A dirty pump not only filters worse, it also works forced and breaks down sooner.
As professionals in maintenance and sales of filtration equipment, we explain how to clean each key part of the system: prefilter and basket, pump turbine, filter (sand or glass) and what signs indicate that cleaning is no longer sufficient.
With daily use, the pump and filtration system accumulate organic debris, scale, sand and fine dirt. This accumulation causes a progressive drop in performance and forces the engine to work harder.
When the pump is dirty, it is common to notice that the pressure decreases, the flow rate is not constant or unusual noises appear. If not acted upon in time, the problem will eventually affect the motor seal and the motor.
The prefilter is the first point of dirt retention and the one that requires the most maintenance. It should be cleaned frequently, especially during periods of intensive use.
To clean it properly, always turn off the pump, open the prefilter cover and remove the basket. Remove leaves, insects and sand and rinse with water. Take the opportunity to check that it is not deformed or broken, since a basket in poor condition allows dirt to reach the turbine.
Before closing, check the o-ring on the lid. If it is dry or dirty, clean it and lubricate it with neutral petroleum jelly to avoid air ingress and unbrazing.
The turbine is the hydraulic heart of the pump. When partially clogged, the pump loses power and may become noisy or overheat.
To access it , it is necessary to disassemble the hydraulic body of the pump. Once opened, manually remove hair, fibers or compacted sand. Cleaning should be done carefully, without metal tools that could damage the impeller.
If you observe wear, deformations or cracks, cleaning will not be sufficient and it is advisable to consider replacing the turbine or the entire pump, especially if the equipment is several years old.
Although the filter is not a direct part of the pump, its condition has a decisive influence on its performance.
In sand or glass filters, cleaning is usually done by backwash and rinse when the pressure rises above the normal value. This process removes accumulated dirt from the filter media and reduces pump stress.
In addition, periodically (usually once a year), it is advisable to carry out a chemical cleaning of the filter to remove grease and scale that the washing does not remove.
The sand or filter glass is not cleaned manually at every maintenance, but it does require attention in the medium term.
If after several washes the pressure is still high or the water is not filtering properly, it is likely that the filter media is saturated. In this case, the solution is a thorough cleaning with a specific product or replacement of the filtering material.
A bad sand condition forces the pump to work with higher pressure, shortening its useful life.
The frequency depends on the use, environment and type of pool. In residential pools with normal use, the prefilter is usually cleaned weekly, while the turbine and filter are serviced periodically or when symptoms of loss of performance appear.
Ignoring these tasks often results in more costly failures.
There are situations when cleaning the pool pump ceases to be an effective solution. If after cleaning the prefilter, turbine and filter, the pump still loses power, overheats or starts to run dry, there may be internal wear, electrical problems or leakage.
In pumps with many years of use, replacement is often more cost-effective than continuing corrective maintenance. As specialists in the sale of Filtration pumps, we recommend the ESPA range of pumps for their ease of maintenance, easy access to the prefilter and greater durability of components.
Turn off the pump, clean the prefilter and basket, check the turbine for loss of power and flush the filter when the pressure increases.
It depends on the use, but in high season it is usually necessary to do it once a week.
It is necessary to disassemble the hydraulic body and manually remove accumulated debris. If the turbine is damaged, it should be replaced.
By periodic washing and, when necessary, with specific cleaning products or by replacing the filter media.
The pump loses performance, heats up, consumes more energy and its service life is significantly reduced.
When the equipment is old, has recurrent breakdowns or the loss of performance persists after complete maintenance.
PoolComet choice
Select options
This product has multiple variants. The options may be chosen on the product page
Pool and Hair Color. Discover how to enjoy a dip in the pool without damaging your hair, keeping it beautiful and vibrant.
Know what a biological or natural pool is, how it works and the best plants to keep it clean and healthy. Enjoy a chemical free bath.
Discover how the spa ozonator can improve the quality of your water and your relaxation experience.
Seleccionar categoria
